Showing posts with label Samelius. Show all posts
Showing posts with label Samelius. Show all posts

Job Number 180107

Here's a Trenton pocketwatch that has a special story.
This watch was given to my Grandfather by his instructor, William Samelius, at the Elgin Watch College.
William Samelius was well known at the time as a watchmaker and educator. He was referred to as "The Dean of American Watchmaking". Students at the college referred to him as "Ol' Bill".

William Samelius made quite an impression on my Grandfather. He spoke of his teacher often.


The back of the watch has the initials WHS and "No 12" engraved.

See the entire album for this project here.
ES034

Information Please!

From The American Horologist magazine, July, 1944

Information Please
Directed by 
W. H. Samelius, Chairman 
Science of Horology and Technical Advisory Board

HRG: I have an Illinois 60 hour Bunn Special watch. Please advise if this watch should be wound every 24 or 48 hours?

Ans.- In all watches the maianspring power delivered varies throughout the running period of the watch. By designing the watch to run 60 hours, the variation of power during the first 24 hour period is less than the variation of power during the latter 24 hours so for that reason, as the mainspring delivers more constant power for the first 24 hour period, it is advisable to wind the watch each 24 hours. If you accidentally omit winding the watch after the first 24 hours, it naturally will keep running until the end of its running time, but the time piece is very likely to take a different rate during the latter part of the run, therefore, we repeat, to obtain a constant rate, it is best to wind your watch each 24 

JIT: When a watch is marked adjusted to heat and cold, 5 positions and isochronism, what is meant by isochronism?

Ans.- The word "isochronism" is derived from the Greek word meaning "equal time." As applied to a watch or timekeeping instrument, the term "Isochronism" means that the time or rate would be constant throughout the 24 hour period, that is, it will have a constant gain or a constant loss for each hour of the day. Theoretically, a balance and hairspring should oscillate at the same rate whether the arc of motion is low or high, meaning that the balance should return to center in the same length of time, regardless if the arcs are unequal during the 24 hours due to the variation of power. The resistance of the hairspring must be equal to the force of the balance. As all hairsprings are not isochronal; it is some. times necessary to test several hairsprings before one is found that will prove itself isochronal throughout the range of balance arc. The length of the hairspring has a great deal to do when striving for isochronism.

HMU: A friend informs me he always puts oil on a roller jewel? 'Is this good practice?

Answer - Oiling the roller jewel is bad practice as the oil soon turns black or will thicken or gather dust, which will soon have effects on the watch. If oiling the roller jewel was the proper thing to do, I am sure all watch factories would adopt that method, however, up to date, you will find all watches as delivered by the manufacturers, are left with the roller jewel dry.

YKG: When inserting teeth m clock wheels, is it advisable to use hard solder?

Answer - When inserting a tooth in a clock wheel, a dove tail slot is cut into the rim, a wedge filed to fit the slot and held fast by spreading or riveting the wedge to place. If hard solder· is used, the heat would take the hardness away from the teeth of the wheels when they would very likely bend over and cause trouble when the wheel is put into service. It is even advisable to avoid using soft solder when inserting teeth into clock wheels.

In the sixteenth and seventeenth centuries, an HOUR glass was standard equipment in the church, so the sermon wouldn't last too long. 



Information Please!

From The American Horologist and Jeweler magazine, January, 1946


WMck - Will dipping watch parts in cyanide leave any bad effects?

Answer - If the parts are guilded and left in cyanide solution too long, the solution will dissolve the gilding, leaving the plates dull and dark. When dipping watch parts in cyanide solution, the parts should first be cleaned in naphtha, the naphtha washed off in soapy water and then rinsed in clear water. Give a quick dip in cyanide. You must bear in mind that cyanide only removes tarnish and if the tarnished surfaces are not perfectly clean, void of oil Or grease, the cyanide will not attack the tarnish. After the cyanide dip, parts should once more be thoroly rinsed in warm soapy water or warm water to remove the cyanide. Cyanide solution itself is slimy and cold water will not give a thoro rinse. After the parts are thoroly rinsed, they may then be dipped in alcohol and dried in warm sawdust. This may sound like a long procedure, however. to get good results, the above care should be taken when using cyanide. Cyanide is poisonous and the user should be cautious not to allow cyanide to come in contact with any cuts or sores. He should also be cautious not to inhale cyanide fumes.

AEW: When was the minute and second hand first used?

Answer: The minute hand (concentric with the hour hand (was first applied by Knibb and Quare and other English clock makers about 1670. No definite information is at hand when the first second hand was applied, however a clock built by Tompion of England employed a second hand constructed by him in 1676 A.D.

BW: How do you test a watch for isochronism?

Answer: The isochronal test for the watch is made by winding a watch fully, setting it on the second and then checking the time each hour throughout the 24 hours. This will show how the rate varies as the watch runs down. If the watch shows a constant gain or loss, each hour throughout the 24 hours, we can then say that the watch is adjusted for isochronism. Checking the watch or making alterations to cause isochronal rates can some times be accomplished through the regulator pins, by opening or closing, then again by reforming the overcoil, changing the elasticity at the bends of the overcoil. It may be necessary to fit a new hairspring. which may be a trifle longer or shorter. The object is to create the resistance of the hairspring to equal the force of the balance, so the balance will be returned to the zero point the same duration of time whether the arc be short or long.

MElNc'D: How can I improve the tone or sound of the gong in a mantle clock? When the clock was new it had a clear tone, but now the tone is very dull.

Answer: May I suggest you examine the leather buttons in the hammer. The leather ages with time, sometimes becoming quite hard and occasionally seem to deteriorate, becoming soft and falling apart. When the leather hardens, you will have a harsh tone or metallic sound. If the leather has softened or becomes spongy, you are likely to have a very soft tone. If the leather lining in the hammers are all right check the support that holds the gong. See that the gong is well secured to the support and that the support is rigidly secured to the base board. See that the base board is held firmly. Sometimes the base boards dry out so they become loose or possibly the base board or soundingboard may be cracked.

ABP: I am about to purchase a watchmakers lathe, motor and staking tool. Will you kindly advise which is the best lathe. 

Answer: The writer is not in a position to mention makers names or comment on their quality. I would advise you to rely on the judgment of an experienced watchmaker who might accompany you on your shopping tour and from his experience of handling tools will recommend what is best to purchase.

TNB: I am thinking seriously of going to school to learn the art of watch repairing. When my course is completed, does the watchmaker have to supply his own tools and material, or does the employer supply them.

Answer: A journeyman watchmaker is expected to have his own kit of tools such as small hand tools, a well equipped lathe with an electric motor, staking tool, etc. However, he is not expected to supply repair parts or any materials necessary to carryon the work. The employer usually is equipped with a cleaning machine, and furnishes the cleaning fluids. He also has a demagnetizer, friction jeweling outfit and crystal grinding machine. A machine for fitting non-breakable crystals, a timing machine and a buffing machine should be supplied by the employer. This applies where a watchmaker is working on a straight salary or commission.

RGO: I have a mantle clock whose case is made of cast iron and finished black. What can I do to restore the black polish that has become dull from years of handling?

Answer: If you have one of the early American made clocks, these cases were usually coated with aspheltum varnish and baked at about 300 degrees F. A very satisfactory job can be had by rubbing the surface with rotton stone and olive oil, using a felt pad, when all scratches have been removed a lusterous polish can be had by vigorous rubbing using a flannel cloth.

JFH: I have noticed, after fitting a balance staff that a watch takes on a new rate, either fast or slow. I am very careful about trueing the balance and also for poise.

Answer: Replacing a balance staff is a major repair that has to do with the heart of the watch. Even when you say the balance is in good poise and true, other conditions may not be the same as before the staff was fitted. For instance, the balance may be a trifle larger or smaller, the larger pivot would show a fast rate, the smaller pivot slow rates. The pivot ends may be of a different shape than the original staff. Flat end pivots will cause fast rates, round end pivots will cause slow rates. When replacing the hairspring, it may take on a slightly different position such as the reg sweep in the regulator pins. Your hairspring may not be perfectly centered nor develop properly. This all has to do with timekeeping. Your tweezers or screwdrivers may be more or less magnetized. transferring the magnetism to the hairspring or balance. The end shake of the balance pivots might be more or less than the original. There are many reasons why the new balance staff you are placing in the watch may not perform exactly as the one removed. However, the change in rates will not be so great but what slight regulation will bring the watch to time.

AFH: I have trouble with the gummed paper clock dials holding fast. They seem to hold for a few days but peel off. What can I do?

Answer: The ready made gummed clock dials have been prepared with a special glue and will hold if proper precautions are made. This may be done by scrubbing the surface of the dial plate with emery or sand paper until the surface' is bright and clean. Moisten the gummed dial, place it in position and place the dial under pressure with some convenient weight for a period of 15 or 20 minutes until the gum is set. This will prevent the dial from warping away from the metal.

AFH: I have noticed that paper clock dials I get from jobbers seem to have a soft surface and are subject to finger prints and dirt. It there any thing I can do to them to aid keeping them clean and washable.

Answer: Make a thin solution of grain alcohol and white shellac, apply two or three coats until the paper surface is glossy. Allow each shellac coating to thoroughly dry before applying the next coat.

HFG: Can I reform a flat hairspring to an overcoil pattern and will it keep the same time as when it was flat?

Answer: To over coil a flat hairspring is permissible if space permits. To do a good job, the hairspring stud should be moved towards the center as well as regulator pins. The radius for stud and reg pin should be 2/3rds radius of hairspring from center. Then you can shape the flat spring to conform to the position of reg pins and stud. Usually, a flat hairspring that has been reformed will show a gaining rate but not so much but what it can easily be taken care of by the addition of a very light timing washer or by moving the regulator. 


Front and back views of unusual and fine repeater watch owned by Ira Leonard of California. Photos by J. E. Coleman, Nashville, Tennessee. 

Information Please!

From The American Horologist and Jeweler magazine, February, 1942


Information Please!

By W. H. SAMELIUS

P.W.A.: - I have been instructed to carefully true compensated balance in the round and poise them. When this is done, I find on returning to work the next morning, after the shop has been cold all night, that the balance is out of round. Should I true such a balance again after assembling the watch?

Ans: - A compensating balance can only be trued and remain so at one temperature. If you true the balance at 70° F and leave it on the bench overnight to get cold where the temperature probably dropped 20 or 30 degrees you will find the balance rims have moved outward and the balance out of round. In other words, the brass rim will have contracted more than the steel rim and the cut ends of the rim will extend beyond the length of the arms. You will note that as soon as the room temperature has increased to the same temperature as when the balance was trued, it will become true again, or back to its normal form.

B.S.: - How can I make a simple cement for patching broken porcelain watch dials?

Ans: - In a clean vessel, dissolve pure white wax and mix with an equal amount of zinc white. When cold, the cement can easily be pressed into the broken places in the dial. Heat the dial slightly to make the cement flow and adhere to the surface. Cleanliness in mixing and a little heat will contribute to the production of a very white wax.

JR.L.: - I see in the late Elgin Catalog and bulletins, an announcement of a patented grooved balance staff which has been introduced. Without a doubt, this proves to be a valuable timesaver for the man at the bench.

The fact that the new staff can be driven out and not injure the balance wheel and that a new staff can be staked to the wheel, leaving the wheel perfectly flat, so no or very little truing is required and that the balance will remain in poise, is a great step forward, but how can I distinguish the new staff from an old staff when a watch comes to the shop for repairs.

Ans: - The difference between the regular model staff and the new model grooved staff is that the waist, or hub on the regular staff is tapered, where the new model staff has a straight hub.

P.D.: - I am having trouble in attaching gummed paper printed clock dials, so the dial will stick and stay flat and smooth and not peel off after a few days.

Ans: - The surface of the metal dial must first be prepared by removing the old paint with paint remover. Thoroughly clean the surface by using coarse sand paper. Wet the gummed side of the dial with a cloth and when ,Nell moistened, attach paper to metal disc laid on flat surface, then with pads and weights, hold the dial down tight until dry. You will then have no further trouble.

E.L.O'B.: - Would like to know what causes the cannon pinion to raise up off center post, no matter how tight the cannon pinion is put on?

Ans : - This question is often asked and the illustrations show the causes for cannon pinion raising. 


Figure No. I - shows center post tapered at the lower end so when cannon pinion is applied, it will have a tendency to raise upward and become loose.

Figure No.2 - shows center post of equal diameter from top to bottom but with the groove slanted upward instead of downward toward the base of the arbor. A cannon pinion fitted to this center post will also cause the cannon pinion to climb up and become loose. 

Figure No.3 - shows center post of equal diameter from top to bottom with the groove so shaped that when the cannon pinion is attached, it will have a tendency to work downward and remain on the post. When fitting a new cannon pinion, make sure the pinion fits freely down to the shoulder of the post. Then by inserting a brass wire in the hole of the cannon pinion, placing the cannon pinion in a V stump and with a center punch, make a small indentation or bulge that will come just below the groove of center post, as indicated by arrows.

Occasionally, we find a cannon pinion, after being placed on center post, that has a tendency to turn rather hard. This may be due to a rough hole in the pinion or rough surface on center post. In such a case, it is permissible to lubricate the center post. 



Helpful Hints

From The American Horologist and Jeweler magazine, February, 1942

Helpful Hints

By W. H. SAMELIUS

Never, when taking a movement apart, with hollow center pinion drive the post out without supporting the bridge in some manner; it is usually very thin and easily bent, but almost impossible to restore to it's original appearance when a bend has once got into the surface.


Never scratch the number of your watch record on a case where it can be seen without the aid of a glass; some reckless tinker so mars the beauty of the case in this way as to seriously irritate the owner. We once knew a watchmaker who barely escaped a sound thrashing from the owner of a watch, in which he scratched a number is such awkward scrawlings as to be visible at arms length.

Never put in a mainspring without examining carefully whether any teeth or pinion leaves are broken or bent in the. main, center or third wheel. In so doing you will save yourself the trouble of taking the watch down a second time to repair damage done by the recoil of the breaking spring.

Never pour oil from the bottle into the oil cup; it is wasteful, more being lost by drip than is used, besides the danger of taking up the fine dust adhering to the flange of the bottle. The neat, handy economical way is to dip your oil wire to the bottom of the bottle and it will take away two or more drops if raised quickly. Let this fall into the oilcup until you have taken sufficient quantity. 



Single Pin Escapement

From The American Horologist and Jeweler magazine, February, 1942

Single Pin Escapement

W. H. SAMELIUS

Ever since the pioneer days of c1ockmaking, when Henry DeVick, in 1365, designed and constructed a Tower Clock for King Charles V of France, scientists, horologists and mathematicians have carried on an endless search for the perfect escapement and since that time, hundreds of escapements have been invented and tested, only to be abandoned and very few survived.

The most common pendulum escapement used today was invented by Dr. Hooke. of England, 1675; it was known as the anchor recoil. We find this style of escapement in most of our mantle and kitchen clocks especially where a short pendulum is employed. It has proven to be practical, easy to adjust and lends itself to production in large quantities.

Another escapement that has stood the test of time and accepted, is the deadbeat escapement, invented by George Graham of England during the early part of the 18th century. The deadbeat escapement is employed for long pendulums, such as second's beat regulators, in fact, many of our most accurate timepieces today are equipped with a Graham Dead-Beat.


Another escapement that has been universally used, was invented by J. A. LaPaute, a French clockmaker, known as the pin wheel escapement. It was a deadbeat and has been favored since 1750. Of later years, it has been discontinued, but many specimens of this escapement are still to be found in jewelry store regulators. The heavy grid-iron pendulum is generally associated with LaPaute's escapement.

Another escapement that has proven it's practicability, especially for tower clocks, is the gravity escapement, invented by Dennison of England, 1854. He designed and caused to be constructed, the Tower Clock in Westminster Tower, London, called "Big Ben." For this achievement, Dennison was awarded a Lordship (Lord Grimthrope).

There is still one more· escapement that is to be found in Observatory clocks. Namely, the "Rieffler Clock and Rieffler Escapement." Generally speaking, most all observatories throughout the world use the deadbeat escapement or the Rieffler escapement.

Among the discontinued escapements we find a very simple one, perhaps the simplest of all, known as the Single Pin, invented by Charles McDowell of Wakefield, England, He was a clever horologist making many outstanding masterpieces, many refinements and modifications in clock constructions, also inventing the single pin escapement. He died in 1872 at the age of 82. The accompanying illustration shows his method of maintaining a pendulum in motion.

The escapement consisted of a roller attached to the projecting pivot or the escape wheel pinion, an impulse pin being fastened into the roller. The impulse pin and roller rotated anti-clockwise. Impulse was imparted to the vertical section of the upper pallet, the pin would then drop off to the horizontal section of the lower pallet. On return of the pendulum, the pin would slide through the space between the two pallets, returning, giving impulse to the vertical face of the lower pallet, the pendulum being pivoted. The weight of pendulum bob would naturally cause considerable wear and friction on the upper support, detrimental to the life of the clock and another objection was the escape pinion would make one complete revolution for each two impulses, necessitating a greater number of wheels and pinions in the train, this also was objectionable and did not prove practical for production and was finally abandoned. 







Salvaging Jewels

From The American Horologist and Jeweler magazine, February, 1942

Salvaging Jewels

By H. B. SMITH Drawings by W. H. Samelius

As jewels are becoming scarce and more expensive every day, I gathered all the old watch movements laying around the shop and removed the jewels and settings. 

As a rule, these jewels' settings are all held in place by screws. The settings are usually of large diameter and thick and can easily be converted into friction settings. 


By cementing the jewel to the end of a brass wire and centering the jewel hole by means of pegwood (Fig No.1) the old setting can easily be turned to desired diameter and thickness as shown in (Fig. No.2) the shaded section having been cut away. If the setting is of correct diameter, it's thickness can be cut down by placing the setting in a wire chuck and use of stepping device, or using the auxiliary jewel chuck. Quite often I run across 0 size 7 jewel watches that did not have removal bushings. I open the holes in the plate, insert a friction setting and get excellent results from the long life of the repair. Using a polished graver, I get bright bushings that have the appearance of a factory job. Incidentally, it keeps up your lathe practice and uses material that otherwise may be discarded.


Information Please!

From The American Horologist and Jeweler magazine, February, 1946


HGG - Can you tell if there is an easy method to determine the full diameter of the pinion to fit any given wheel without extensive calculating? I want to select a 6 leaf pinion to fit a wheel. Is there any easy formula that I can follow and get a smooth running gear?

Answer: The correct way to arrive at the proper diameter for a pinion is by mathematics, however, you asked for an easy method and one that is practical so the following formula will prove helpful and satisfactory for all practical purposes.

The full diameter for a 14 leaf pinion should equal the distance of 6 teeth from point to point on the driving wheel. For a 12 leaf pinion, the diameter for pinion should equal the distance from tip to tip of 5 teeth. For a 10 leaf pinion, the diameter should be 4 full teeth. For an 8 leaf pinion, the width of 4 teeth measured at their points deducting 1 space. For a 6 leaf pinion, the distance of three teeth measured from the point. If these measurements are carefully followed, the pinion will be usable.

RHY: What kind of grease is used to keep moisture away from crown and stems in waterproof cases?

Answer: Riggs Gun Grease is used to pack in the pendant and around the stem. It also acts as penetrating oil when the steel parts are badly rusted.

JC: Recently I purchased a package of diamond dust, expecting to use it for resurfacing and polishing pitted cap stones. I find the powder too coarse. Is there anything anything I can do to take out the coarse powder?

Answer: Procure five small glass vials of about 1 ounce 'capacity, mark vials from 1 to 5. Fill dial No.1 with clock oil and thoroughly stir diamond powder into clock oil. After ten minutes pour off the oil into bottle No.2, allowing that to stand 45 minutes, repeat and pour off into bottle No.3, allowing it to stand 24 hours. Repeat and pour oil into Bottle No. 4 allowing it to settle for 24 hours and finally pour remaining oil into bottle No.5 and allow to settle until clear. You will now have 5 grades of diamond powder. No. 3 and No.4 for fast cutting and No.5 for polishing.

ECB: Please explain the use of different watch brushes, at what stages are they used, purpose of each brush and cleaning, of bridges and cases?

Answer: As a rule the watchmaker is equipped with three grades of watch brushes, fine, medium and coarse. The fine brush may be used for brushing sawdust or other fine lint from train wheels or plates of the watch that has passed thru the sawdust method of drying. The fine brush may also be used for dusting the dial without danger of damaging the hands. The medium brush may be used for brightening the watch plates that may be spotted or slightly tarnished, especially after the cleaning solution has failed.

By charging the brush very lightly with rouge, a vigorous brushing will brighten the plates. The balance wheel can also be greatly improved by using the brush charged with rouge. A stiff brush can be used for brushing and brightening cases or bands. This brush should also be charged with rouge. A stiff brush is also used for brushing clock plates, wheels and pinions, using naphtha for solvent. 

It is suggested if you are using new brushes that the bristles be run across some rather coarse sand paper so as to take the sharp corners off the end of the bristle, or the brush may be run across the sharp edge of broken piece of glass, which will serve the same purpose.

PD: How can I true a solid balance wheel in the flat. I seem to have more trouble with solid balances than the cut balances.

Answer: When trueing a solid balance in the flat, the first move is to check the level of both arms. If they are not of the same level, bend the arm up or down until you get desired results. Check the rim between the arms. If they are not of equal height, carefully twist the arm until the rims are level. When twisting the arms, care must be taken that you do not bend the arms up or down throwing that section of the balance out of flat. With a little practice, you will soon accomplish and conquer what may seem like hard jobs, when in reality it is very easy compared to the split balance.

MEC: You ask if the only way to bring the dial position and pendant position to correspond in a wrist watch is by shaping the ends of the pivots.

Answer: There is a limit to how much time you can alter the rates by altering the balance pivots and in many of the small watches the balance pivots are quite large, consequently showing a fast rate in the pendant position over the dial position. By flattening the ends of the balance pivots, you will increase the dial position, however, there are times when the balance pivots are so large that you cannot control or bring the two rates close together, unless small pivots are used which would then give you a slower rate in the pendant position which would compare favorably to the dial positions. Many of the factories deliver their watches with a tolerance of a minute to 1 1/2 minutes plus or minus in 24 hours. 



Unusual Clock

From The American Horologist magazine, February, 1946

Unusual Clock

By W. H. Samelius


This clock is built in the form of a light house, the tower has a lamp with a light that flashes. It has nine dials showing correct time ,for the principal cities around the world. The center dial showing local time. A synchronous motor located in the house drives the spider holding the dials, making one revolution per hour. From each end of the arbor of the spider is a small projecting stud. On this stud the dials revolve, the dials being weighted so that figure 12 will always remain on top. A frame to which the dials are attached is recessed to receive the cannon pinion, minute wheel and hour wheel. Figure No.1. The cannon pinion being friction tight to the stud will then hold the minute hand in any fixed position or time it may be set. Instead of the minute hand revolving, the dial revolves about it's center as the spider revolves, thus showing the time to the minute and hour. The complete clock stands 16 inches high, the spider is ten inches in diameter and each of the small dials are 2 1/2 inches in diameter. The dials are engraved showing the cities of Bombay, London, Hawaii, San Francisco, Yokohoma, Shanghai, New York and Moscow. This clock was constructed by Mr. William Geoghagen, student at Elgin Watchmakers College. He is to be complimented for his skill and careful workmanship. 




A Tickless Clock

From The American Horologist magazine, February, 1946

A Tickless Clock

By W. H. Samelius


Many attempts have been made to create a tickless clock or silent escapement. Illustration of such a clock is one of the attempts that can easily be made by a workman who is equipped with a wheel cutting attachment for the lathe.

The figures for number of teeth and pinion leaves are shown in the illustration and it is up to the workman to decide the size of clock he may choose to construct.

Instead of the regular escape wheel and pallet, a small crank is attached to the last pinion, or driver. A horse shoe spring is connected between the crank and pendulum rod, the loop end of the horse shoe spring must fit freely over the studs that do the driving and some experimenting may be necessary to create a spring that will not allow the drive pinion to run wild, but a spring with tension enough to hold the drive pinion in check while the pendulum is making' it's excursion. The train is designed for seconds beat pendulum 39.14 inches long, measured from point of suspension to the center of the bob.

The drum is to be made large enough to take 16 coils of cable when the timepiece will run for 8 days. If carefully constructed, this clock will give satisfactory results and be perfectly silent when in motion.



To Repair Clock Escape Wheel

From The American Horologist and Jeweler magazine, October, 1938

To Repair Clock Escape Wheel

By W. H. Samelius

When repairing clocks we often find the escape wheel out of round and the escapement cannot be adjusted to function properly under such conditions. To repair the escape wheel is not a complicated job and can be done quite easily.



You mount one end of the arbor in the lathe, supporting the other pivot by means of a female center in the spindle of the tail stock. Then by raising the T - rest as high as it will go you use it as a means to support a very fine file or oilstone. Then when the lathe is in motion you take a very light cut off the top of the teeth until the wheel teeth are all the same length.

After this operation it may be necessary to cut the thickness of the tip of the teeth. To do this, use a fine cut file and cutting the front of tooth only until desired thickness is obtained. N ever attempt to file both sides of an escape tooth as the results may be disappointing.

You are apt to find the spacing from tooth to tooth vary. In other words, the circular pitch of the teeth will be irregular, making it impossible to set the pallets and getting good results. Figure No.
1 shows mode of procedure.

Clock pivots should be well polished to make a free running train. The work is easy and very simple.

Make a hardwood support with V-groove as shown in Figure No.2. It must be a close fit that there is no danger of slipping after once locked in place. Fasten wheel arbor in lathe chuck seeing that the V-groove is high enough to support the pivot to be burnished on center. Run the lathe at fair speed and use a burnish back file that has been cross-lined with a No. 2 emery buff stick. Take a few strokes with file applying a fairly good pressure and the results will be a highly burnished pivot.

See that edge of file is also cross-lined with a No. 2 emery buff stick. You will then have a nicely finished square shoulder. Any further detail is hardly necessary as cut is self-explanatory. (Figure 2. ) 


Information Please!

From The American Horologist and Jeweler magazine, March, 1942


HES :- How is a watch adjusted to positions, what makes the time between the side positions differ if there is as perfect a poise as possible, on the balance. Is it possible to adjust a watch to six positions?

Answer :- To fully answer your question would just about fill a book, however, you say the balance is in perfect poise; and the rates vary when watch is on edge. These variations can be caused by many other influences besides a balance that is not in poise. For instance: The hairspring must be perfectly circled to the collet, the overcoil formed so the spring develops equally in all directions and contracts equally in all directions. The regulator pins must be close and the spring perfectly flat. Sharp bends where the spring is fastened to the collet must be avoided and the hairspring pinning point in it's proper position. It should be pinned so if we drew an imaginary line thru the center of the balance when the watch is held with the pendant perpendicular, the spring is pinned on this horizontal line and to develop up over the collet. This may be either to the right or to the left. The balance pivots must be truly cylindrical and both pivots finished flat on end, being careful there is no burr on the edge of pivots. The hole jewels must be equal size and thickness, olive shaped. The corner freedom for jewel pin as it enters and passes out of the fork slot, must be equal on both sides.

The guard pin close but in no case or position should it contact the safety roller. The end shakes in your balance, pallet arbor and escape pinion must also be very close and all three of equal amount. The escapement must be set so there is a safe drop lock and some slide. Ordinarily, if your total lock and slide is equal to 1/5th the width of the pallet stone, you will have a satisfactory escapement. See that the draw, or draft, is ample by slightly lifting the lever from the banking screw and if the lever does not return to the banking screws, it will indicate there is insufficient draft and if that is the case, the guard pin will drag on the safety roller, causing a variation of time in different positions. The roller jewel must be a close fit, well proportioned, by that we mean two fifths of the diameter being cut away, leaving a flat face. A jewel so proportioned will not present a sharp edge as it enters or passes out of the fork. Examining the balance pivots with the ordinary eye loupe does not show the small defects that go to make trouble when timing a watch to positions, we recommend using a microscope, as the least irregularity on the surface of the pivot or it's contour will be detrimental to timekeeping qualities.

Examining the cap jewels carefully for any pit marks from wear and also see they are set perfectly flat. Hone cap jewel is flat and the other cap jewel out of flat, the watch will invariably show a gaining rate when running on the out of flat cap jewel.

To get best results and a most constant rate, a 1 1/4 turn of the balance or, 450 degrees, is desirable. Changing the strength of the mainspring to obtain the proper balance arc is advisable.

Generally watches are adjusted to five positions, namely dial up, dial down, pendant up, pendant right and pendant left. The greatest error between any two positions lies between the pendant up and the pendant down, due to position of pinning point. The sixth position would be pendant down and as the watch is not carried that way, that position is disregarded.

A.P. :- 1 have heard our head watchmaker telling about cutting a contrate wheel for a Swiss watch.
Tell me what make of Swiss watch has contrate wheels, or are they to be found in complicated watches only?

Answer :- A contrate wheel is one that has two sets of teeth, that is, a gear wheel that have a ring of teeth, standing at right angle to the plane of the wheel, while the other set of teeth are on the periphery of the wheel. You will find contrate wheels on all new model American watches and many Swiss models, they are cataloged as Crown wheels or main wheels. 


Pallet Stones

From The American Horologist and Jeweler magazine, March, 1942

Pallet Stones

W. H. SAMELlUS

Setting up the escapement is an adjustment that many of our younger watchmakers seem to fear and finding the cause for poor motions is quite often overlooked for want of experience, and perhaps, knowledge. The illustrations may prove helpful and assist the younger men with their work. 


Figure No. I - The escape tooth at rest against the receiving stone. The total lock, which means, initial drop and slide, should not be over one fourth the width of stone. For high grade watches, the total lock can be reduced so that it would be 1/5 to 1/6 the width of the pallet stones. 

The draft angle of the stone and the clearance on the face of the tooth is so that the toe of the tooth itself is resting an the face of the stone. Conditions of this kind are ideal, causing very little friction as the tooth is unlocked from the stone. There will be no oil adhesion.

Figure No. 2 - The discharged tooth after it has left the discharge corner of the discharge stone. The space between the corner of the stone and the heel of the tooth is called "drop" or clearance. The escapement should be examined carefully that the drops are equal for the receiving stone and the discharge stone.

Figure No.3 - Condition where the receiving stone has insufficient lifting angle and the sharp corner of the stone riding the face of tooth.

This is called "engaging friction." When conditions as in Figure No. 3 exist, very little power can be delivered from the receiving stone. A new stone substituted, having a greater lifting angle, will be required.

Fig. No.4 - Same condition and is commonly met up with, as many men are not aware that the discharge stone has a greater lifting angle than the receiving stone. If conditions are found in the watch, similar to figure No.4, it is safe to assume that a receiving stone has supplanted a discharge stone. Replace with a discharge stone.

Figure No. 5 - Shows tooth as it has passed beyond center of stone and is now giving the last half of its impulse.

Note the discharge corner of the stone riding up the incline of the tooth and the clearance between the heel of the tooth and the face af the stone. This is the correct action for our modern escapement.

Figure 6 - Shows the tooth midway across the face of the stone, the lifting angle of the tooth and the stone is parallel. This condition is often found and is especially detrimental in our small watches. If the oil in the escapement is heavy, there is strong adhesion between these two surfaces and the breaking of the oil adhesion retards the free action of the tooth and pallet.

Figure 7 - Shows the tooth at rest with the pallet stone setting at right angles with Tangent Line A.

The pressure of tooth resting on the face of stone creates a direct thrust to the pallet center and would act very much the same as a dead beat escapement. There would be no tendency of the pallet stones to slide down on the toe of the tooth, drawing the lever up to the banks. While conditions as severe as the illustration rarely exists, we meet up with watches where the pallet stones have been tilted sufficient to create a draw. If there is insufficient draw, the lever will not hold up to its banks, the guard pin will drag on the safety roller. creating a poor motion or possibly, stopping the watch entirely.

Figure No. 8 - Shows tooth at rest against the discharge stone. In this case the discharge stone has been tilted too much so instead of the toe of the tooth resting on the locking face of the stone, the corner of the stone is resting on front of the tooth. When conditions similar to Fig. No. 7 or 8 exists, it is possible to remedy the trouble by moving the stones sideways in the pallet frame and if results cannot be obtained, it will be necessary to enlarge the slots in the pallet frames so that the stone may be tilted sufficiently to create the proper draw, Fig. No. 7 and diminish the draw for Fig. No. 8.


Figure No. 9 - Shows the tooth as it has passed one half way across the face of stone. Note the condition that the toe of the tooth is riding the smooth lifting plane of the stone. This is an ideal condition where Fig. No.5 shows the path of the tooth after it has passed the center of stone and the discharge corner of the stone is riding the incline of the tooth.

Fig. No. 10 - Shows tooth at rest on the face of the pallet stone, however, note the toe of the tooth is worn. When a case of this kind exists, there will be no draw to hold the lever to its banks, allowing the guard pin to drag on the edge of the roller table, slowing up the motion of the balance. A case of this kind is best remedied by replacing escape wheel.

Figure No. 11 - When tooth of escape wheel is badly worn or damaged, the watch may run but we are only getting about one-half impulse, adjusting the pallet stones in such a case, would be of no avail. Replacing the escape wheel IS the best remedy.

Figure No. 12 - Shows tooth at rest with the receiving corner of the pallet stone chipped. This would cause the pallet to be thrown away from the banks, crowding the guard pin against the edge of the roller, causing' poor motion and many times, stopping the watch. The sharp edge of the stone would also be detrimental as it would soon cut the face of the tooth.

Figure No. 13 - Illustrates a narrow pallet stone, the position' of the stone indicates that the draw will be very strong and that the lifting angle will be excessive, causing a heavy drop lock on the discharge stone, being a narrow stone, the impulse would be considerably less then on the regular stone.

Figure No. 14 - Illustrates the pallet stone that is too wide. The slot in pallet frame has been spread to accommodate the stone. Illustration shows there will be no outside drop and very likely, the discharge corner of the stone would strike or be interfere with by the heel of the tooth.

The interference, however, slight it might be, will cause poor motion or stopping of watch.

Figure No. 15 - Before setting pallet stones to their proper positions, for drop lock and slide, the jewel pin and guard pin action must be adjusted. See that the jewel pin is set upright centered to the crescent, and the face of the roller jewel squared to center. Place balance in watch and turn the banking screws so the corner of the fork slot is brought close to the corner of the roller jewel. This is generally known as corner freedom and for the average watch, this corner freedom can be .001".

Fig. No. 16 - Now advance the roller and balance until the guard pin is out of the crescent. If the guard pin is tight against the roller, shorten it until there is a guard pin clearance or freedom. This freedom between the guard pin and safety roller should be .0005".

Fig, No. 17 - This rule applies on all watches so that should the lever get a jar and leave the bank, the guard pin will still hold the lever in the proper position so that the jewel pin will enter the fork slot freely.

When the jewel pin action and guard pin action have been satisfied, then the pallet stones are set so that there will be a safe drop lock and a visible slide. The banking pins are not adjusted ta create slide after the stones have been set. When replacing pallet stones, always order genuine pallet stones for the make and model of watch you are working on as each factory designs escapements to their specifications so that pallet stones a,re not interchangeable from one makers watch to some other makers watch. 


Information Please!

From The American Horologist and Jeweler magazine, April, 1942


]S: - 1 have been a subscriber to the American Horologist for several years and enjoy reading questions and Answers. Here is one I have not seen answered yet: I sometimes find a cannon pinion that is tight all the way down; until it just gets to place then it is loose. Please advise how to remedy this trouble. 


Ans: - The illustration shows a center arbor with a groove, or relief. As you state the cannon pinion goes down tight part way and then becomes loose when finally seated. If is it a cannon pinion that is not slitted for tongue tension, you will have to insert a brass wire into cannon pinion, laying the cannon pinion on small V-block and with center punch, create a bulge inside the pinion high enough so it just goes over the edge of recess in center arbor. In other words, the bulge, or tongue in cannon pinion tube must come down just below the slanted, or tapered groove of center pinion. If this does not remedy your trouble, I would advise procuring a new center arbor. The illustration shows, one side of the cannon pinion Fig No.1, where the bulge of the cannon pinion rides free in the recess and Fig. No. 2 where the bulge in cannon pinion rides below the edge of groove of center arbor. The February issue of American Horologist also. deals with this subject.

FS: - Occasionally I want to remove engraving from inside of rings, also from top of signet rings. How can I do this easily and quickly?

Ans: - For removing engraving from the inside of rings, first use half round file to cut dawn the engraving. Then use round ring buff or emery stick in lathe to smooth off file marks. Follow this up with a felt buff charged with rouge.

Far facing off signet, make a wooden wheel about 4" in diameter and 1/2 to 3/4" thick. One that will fit the arbor of your polishing lathe. Charge one side of wheel with tripoli, the other side with rouge. File out engraving from signet ring, press signet ring against side of lap that is charged with tripoli. This operation will remove the file marks and leave the surface flat, when you can finish the job by polishing the surface of the ring an the apposite side of lap which is charged with rouge. Use a moderate speed in polishing which will bring excellent results. Where a quantity of rings is to be faced, a lead lap is used.

RW: - 1 have a fine French clack with an Onyx case. The onyx is very dirty and somewhat discolored. Can you tell me how I can clean and restore the onyx to. its original appearance?

Ans: - Make a paste of plaster of paris and benzene. Apply a coating of this aver the surface of the onyx. As the benzene evaporates, the grease and dirt will be drawn into the plaster of paris, which is then rubbed off. If there is considerable grease in the onyx, the process may have to be repeated. To polish the case, dissolve beeswax in benzene. Apply and polish vigorously, using a flannel cloth.

WO: - At a meeting, one of the speakers referred to a "Clock Watch."' Is this a trade term for some special timepiece?

Ans: - The term "clock watch" takes its name from similarity of construction to our common alarm clock. That is, the clock, which is non-jewelled and in many cases, has lantern pinions, and the balance unit is supported by a balance arbor with cone pivots running in hollow steel screws.
We might say a "clock watch" is a clock reduced to pocket size.

PL: - A friend of mine has an antique verge watch, key wind, chain drive. He says it has a Shagreen case. Please tell what a Shagreen case is made of?

Ans: - Shagreen is a leather made from skin of sharks. By wetting the leather, it becomes soft and pliable and was used to cover the outside of watch cases and many other articles. It was dyed in various colors, watch cases were usually covered with dark brown, dark green or black leather. 

HA: - I recently made a trade and secured an old American Clock, something I have always wished for. After setting it up to run, it continually gains time. I have lengthened the pendulum to the limit, added weight to pendulum, but to no avail, it still gains time. Can you suggest what I can do to make this clock keep time?

Ans: - In building wooden clocks, the wheels were pressed and glued fast to the arbor. Some of the wheels were merely pressed into place without glue and with age, they sometimes work loose. If you will examine each wheel, it is very likely you will find one or more of the wheels loose on their arbors. Sometimes, we have found the small pin that holds the escape wheel fast to it's arbor, has fallen out, allowing the escape wheel to slip. This should solve your problem.

PD: - The watchmaker who held the place before I came here, held the position for some 25 years and he I evidently never threw away a thing. He left a lot of worn out files, drills, broken punches, etc. Is there anything I can do with them. 

Ans: - There is. Broken gravers, too short for turning may be just right for engraving, carving, chasing or stone setting, by slightly altering their shape. The files may be softened by heating red hot and allowing them to cool off slowly by burying them in ashes. You will then have the finest steel for making springs and various other parts of the watch or pallets for clocks or other clock work. Broken punches may be softened by heating to dull reel. When cooled, they may be redrilled, hardened and tempered to a dark straw.

No doubt many of your drills could be resharpened and used, or they could be annealed to a rich blue color and used for turning staffs. The old man saved them because he knew all this and of the value to use the old files, punches, etc., for other purposes, where they would again be useful.



Adjusting Bar and It's Use

From The American Horologist and Jeweler magazine, April, 1942

Adjusting Bar and It's Use

By W. H. SAMELIUS

It is well known among horologists the advantages a fusee has over the regular going barrel, especially in the older watches.

The first fusee invented, is credited to Jacob Zech of Prague and introduced about 1525. It's purpose was to convert the various forces of the mainspring into a constant driving force. All early English watches and chronometers were equipped with a fusee.

The fusee as constructed today has maintaining power, the principle of this maintaining power is to maintain power to drive the train while the fusee is being turned backwards, or the 'watch being' wound, This style of fusee is called "going Fusee", to distinguish it from the plain fusee as found in the verge watch. The maintaining power was invented by John Harrison of England in 1750, a clever horologist and his improvement is regarded as an outstanding contribution to horology. All marine chronometers employing a fusee as well as high grade weight driven clocks are equipped with maintaining power today. As the mainspring always has more turns of power than are actually used, same means of adjusting or regulating this surplus power in order to obtain constant power throughout the 24 hours, was necessary. This brought about the invention of an adjusting rod.


The adjusting rod consists of long rod with a socket an one end, having a square opening and so made that it can be securely attached to the winding square of the fusee. On this rod is a sliding weight that may be held in place by means of a lock screw or tension spring, holding the weight friction tight. The overall dimensions of the rod varied from eight to twelve inches in length.

To adjust the fusee to it's mainspring, assemble the watch complete with the exception of the fourth wheel, which can be put in place later by removing the small bridge from the lower plate. English watches and chronometer, are all constructed making the third or fourth wheel removable without disturbing other parts of the watch.

Proceed to hook the chain fast to the drum, winding the chain an to. the drum then hooking the chain into the fusee, wedging the third wheel. When the chain is fully wound, set the mainspring up and a half turn. Attach the adjusting rad to the winding square of the fusee, Fig. No. 1. Wind the spring by rotating the rod until all the chain is on the fusee and the stop works have arrested further winding. Hold the movement on edge and slide the weight along the rod until a point is reached at which the weight neutralizes the force of the mainspring so the whole rests in equilibrium when left to itself. Turn the rod backwards one turn at a time and if equilibrium is maintained throughout each test, the fusee is well adjusted. If the weight seems to be too heavy for the lower coils of the mainspring, set the spring up another half turn, or more if necessary to increase the tension. In the converse case, of course, the spring tension must be Jet down. Many times the equipoise cannot be obtained due to a spring being set to much, or possibly, too short or too long. It is profitable and time saving to supply a new mainspring.

To Trace the Form of Fusee 

Having ascertained the distance between plates, mark off on a brass plate the height XY of the cone portion of the fusee, that is to say, of the portion on which the chain is to be coiled. The base of the cone, which is XZ, is the radius to be traversed by the Axis AB at right angles. Divide XY into four equal parts, as there are four turns and draw the parallel lines 3, 5 and 7. Now mount the barrel with it's spring and arbor, between the plates and attach the adjusting Bar, Fig. No.3, to mainspring arbor. Before the spring is brought into action, the adjusting weight "C" must be placed at such a position that the lever rests horizontal. Then wind spring one complete turn, taking note of the required amount of weight necessary to bring the lever into equilibrium. Wind the spring through two turns and add weight until equilibrium is secured, noting the total weight added and so on. When the operation is concluded, there will be five weights in the pan "P". The radii of the fusee will be inversely as these weights and it is easy to determine by a simple proportion by taking the radius XZ as unity, what are the radii C3, D5 and G7 and B9 through the points 9, 7, 5, 3 and X, thus obtained. draw a curve, which will give the form of the fusee for that particular spring.


Information, Please

From The American Horologist and Jeweler magazine, July, 1946


GMH: Can you give a combination of wheels and pinions for a Grandfather Clock with a very slow pendulum? Pendulum is about 4 or 4 1/2 feet long.

Answer: To construct a clock with a pendulum such as you wish to employ, I suggest the following train:

Main wheel to have 144 teeth, center pinion 12 leaves, center wheel 96 teeth, third pinion 12 leaves, third wheel 90 teeth, escape pinion 12 leaves and the escape wheel 25 teeth. This combination will call for a pendulum 56 3/10 inches long and will beat 1 2/10 seconds per swing of pendulum.

The following is also a combination you may use: Main wheel 120 teeth, center pinion 10 leaves, center wheel 80 teeth, 3rd pinion 10 leaves, 3rd wheel 75 teeth, escape pinion 10 leaves.
You could also use a 25-tooth escape wheel. This will employ the same length pendulum 56 3/10 inches long.

Different pendulums can be used if you follow the following formula, using the same train as called for above:

Escape Wheel teeth     Vibrations per hour    Length of pendulum
25                                 3000                           56.3 inches
26                                 3120                           51.8 inches
27                                 3240                           48.1 inches
28                                 3360                           44.7 inches
29                                 3480                           41.4 inches
30                                 3600                           39.14 inches

The only pendulum that will show seconds is the 39.14-inch pendulum.

All others will beat slower than a seconds beat, and consequently will not indicate seconds on the dial. The 56.3 inch pendulum swinging at 1.2 seconds per beat will swing 50 times per minute and the seconds bit, or dial, will have to be calibrated into 50 marks instead of the regular 60 marks. It is understood that whatever escape wheel yon may select, a special pallet will have to be made for that particular wheel.

HGE: Can you give any standard for side shake and end shake applicable to railroad watches?

Answer: In general practice, the following shakes are used:
                            End Shake          Side Shake
Center pinion      .02 mm                .015 mm
Third pinion        .02 mm                .015 mm     
Fourth pinion      .02 mm                .015 mm
Escape wheel      .02 mm                .01 mm
Pallet arbor        .015 mm              .0075 mm
Balance staff      .02 mm                .0025 mm
Barrel                 .02 mm                .015 mm
Barrel arbor       .02 mm                .015 mm
     
SHW: How can I determine the proper size drills to be used before threading a hole?

Answer: To determine the proper size tap drill for any tap, divide 1 inch by the number of threads to the inch. If your tap is not marked, you will have to count the threads. The result will be pitch, or distance from tip of one thread to the tip of the next. Then multiply the pitch by .649. This will give depth of thread. Multiplying depth of thread X 2 will give depth of two threads or the amount to be subtracted from full diameter of your tap.

RHS: I am told it is not necessary to poise a balance wheel after fitting a new staff if the wheel is well trued in round and flat. Is this true?

Answer: Regardless of how well you true the balance wheel, it should be tested for poise as you have no assurance that the wheel was in poise before you fitted the new staff. When poising the balance, the roller table is attached. In all first class shops, poising the balance is a "must." Your reputation depends on how well the watch runs after you have repaired it and no watch can keep close time in different positions unless the balance is in poise. That is your first step for building your reputation. After that, the hairspring must be perfectly centered, leveled and its development in and out from center equal in all directions. It doesn't take a customer very long to discover his watch is keeping better time after the watch has been repaired by a workman who will poise the balance and correct the hairspring.

JOC: How can a person tell the time from the bells of a ship's clock?

Answer: The striking mechanism of a ship's clock is constructed so as to strike 8 bells at 12 o'clock, 4 o'clock and 8 0 'clock. . The clock strikes each hour and half hour and one bell is added each half hour until 8 bells are reached, when the clock once more strikes one bell again, thus:

At 12 :30 strikes Ding.
At 1 :00 strikes DingDing.
At 1 :30 strikes DingDing-Ding.
At 2 :00 strikes DingDing-DingDing.
At 2 :30 strikes DingDing-DingDingDing.
At 3 :00 strikes DingDing-DingDingDingDing.
At 3 :30 strikes DingDing-DingDing- DingDing-Ding.
At 4 :00 strikes DingDing-DingDingDingDing-DingDing.
4:30 to 8 and 8 :30 to 12 o'clock, same as above.

RCB: I want to build a decimal clock showing 100 minutes to the hour. The 4th pinion is to turn 100 revolutions to 1 revolution of center wheel instead of the 60 revolutions of 4th pinion and 1 revolution of center wheel. Will you give me the combination of teeth and leaves of pinion necessary?

Answer: You can use the following combination: Center wheel to have 80 teeth, 3rd pinion 8 leaves; 3rd wheel, 70 teeth and 4th pinion 7 leaves. Or any two reductions where the ratio is 10 to 1, suitable for the space allowed between centers.

YAM: Can you give formula for determining the correct driving weight for a Graham Dead Beat escapement, having seconds beat pendulum? 

Answer: There is a formula for making these calculations which would give you the approximate weight. However, there are many factors entering the problem to be met up with, such as the size and condition of pivots, the bearings in the plate and condition of the gearing which all have something to do with the free running of the train. So, instead of going into mathematics to get results, the quickest and best way would be to suspend a container at the end of your cord and gradually fill container with buckshot or sand until you have enough power to drive the escapement. Then, continue adding weight until your escapement shows some slide. It is an easy matter then to weigh container, using the same amount of lead or cast iron for making up finished weight. The brass tube filled with lead of equal weight will then fill your requirements.

APO: Can you tell me anything about the Mozart Watch Company?

Answer: The Mozart Watch Company was founded in 1864 at Providence R. 1., and capitalized at $100,000. It was to manufacture an unusual watch having three wheels, invented by Mr. Mozart. After two years, the model was discontinued and a regular model watch designed by L.
W. Cushing of Waltham. The name of the company was changed to New York Watch Company, and the plant was destroyed by fire in 1870.

JGD: Quite often, after cleaning a watch, I find the hairspring coils have a tendency to stick together. I test for magnetism but none is apparent. Can you suggest what might be the reason for the coils sticking?

Answer: You state there is no magnetism in hairspring. Can it be possible the cleaning solution is old and also the rinse? In time they become impregnated with oil, then as the parts go thru the drying operation some of this thin film of oil is left on the hairspring, becoming sticky and causing the trouble. If your cleaning solution is in good condition, the rinses fresh, you should have no further trouble.

RMC: I have trouble setting roller jewels. I have tried shellac and other cements but somehow the roller jewel becomes loose and falls out of the roller. Can you advise what the trouble may be?

Answer: After selecting roller jewel of proper size, it should be dipped in alcohol to thoroughly clean the surface. The roller table should also be thoroughly cleaned, removing any other shellac or cement. Then when setting a new roller jewel, use new cement or shellac, not applying any more heat than is necessary to cause the cement to flow freely, as the cement will then adhere to the dry surfaces. Overheating the cement will cause it to become hard and brittle and lose its adhesive qualities.

G.AG: Which is the better and quicker method for grinding pivots to size - oilstone powder, corrundum powder or diamond powder?

Answer: We prefer to use a very fine grade of oilstone powder and oil, using an iron grinding slip for grinding the pivot to size. The oilstone powder will not imbed itself into the balance pivots, which is liable to happen if you use carborundum or diamond powder. Pivots that become charged with either of these two abrasives will soon cut the balance hole jewel and cap jewel.

RWT: I find when working on some 7-jewel Swiss watches, that shortly after oiling them the pivots appear to be dry and when testing the watch on a timing machine, it shows very irregular and spotted lines. After reoiling the watch, letting it run for some time, and testing the watch on timing machine, I find the lines are cleared up. I am curious to know if the plates are porous, absorbing the first application of oil.

Answer: The· writer has heard of some research work along this line, experimenting with porous metals. You no doubt are aware that the auto industry uses self -oiling bearings for special parts of its power unit. The metal is made of very porous material being filled with special lubrication under great pressure. Bearings thus treated will remain lubricated for a long period of time and it is possible you have run across some watch plates that have porous material. Naturally, when you clean the watch, what lubrication was in the holes was absorbed. It will require an extra application of oil in order to fill the pores in the metal.

JOC: Will you enlighten me on meantime screws, and how much regulation one can expect when turning them in or out from the balance wheel?

Answer. The balance wheel contains three kinds of screws-the large screws are the balance screws, the smaller head screws such as half head or quarter head are the timing screws, and the screws with the long thread 'and square head are the meantime screws used for final regulation.

When fitting a new hairspring, it is sometimes necessary to add a small amount of weight, such as a quarter head, or even a pair of heavy washers to bring the watch close to time, say within two minutes. It is then the meantime screws may be used to bring the watch to correct time. This is done by turning the meantime screws in or out. Turning them in will cause the watch to run fast and the reverse when turning them out.

When using the meantime screws, be very careful to turn the opposite screw an equal amount, otherwise the balance will be put out of poise, destroying position rates. The use of these meantime screws should not be abused, turning them out too far' so they may be loose or strike other parts of the watch. The following table will give you the approximate results you can expect from the average watch.

Size     Turns of screw             Sec. per hr.
18-16  1 full turn, 2 screws    3 seconds
12       1 full turn, 2 screws    2 seconds
6/0      1 full turn, 2 screws    5 seconds
18/0    1 full turn, 2 screws    5 seconds

Watches employing four meantime screws should only be turned one-half the amount shown on the chart for the same results.


Blog Archive