Showing posts with label B. W. Raymond. Show all posts
Showing posts with label B. W. Raymond. Show all posts

Job Number 260045

The hands were pretty corroded, but I was able to clean them up.

I had an extremely difficult time with this case. For some reason it was more trouble than it should have been. Firstly, the case back pressed in on the movement bridges and stopped the watch. I narrowed the problem down to the 4th and escape bridge, but I suspect the balance may have been an issue too. The case is extra thin, it was hard to get it closed in such a way that it stayed running.

Next, it took me nearly all day to get the front bezel on. It truly barely fits, if you can call this fitting. I have worked on these exact cases dozens of times and not had such difficulty. I had to heat the bezel (to expand it) quite a lot. I almost never have to do that. 

It's on now though, glass crystal and all. I only hope I don't have to get the movement out again.

Elgin number 22813952 is a grade 452, 12 size, 17 jewel, G.M. Wheeler model.

Job Number 260040

Sweep seconds wheel installed... 

Elgin number 41758229 is a grade 581, 21 jewel 16 size,
made about 1942. This is a military B.W. Raymond model with sweep seconds and a GCT dial.

Job Number 260040


Testing for a few days...

Elgin number 41758229 is a grade 581, 21 jewel 16 size, 
made about 1942. This is a military B.W. Raymond model with sweep seconds and a GCT dial.

Job Number 260040

The broken balance staff was not riveted on, or least it wasn't secure. I noticed it was loose while taking the roller parts off. The staff just pulled off, so I suppose that saves some time.



There's a two-piece double roller and the main part was very tight. I was afraid it would crack! I polish the staff body quite a bit (nice shine) and then went very slowly. It went on fine.
Sweep seconds...


New staff, now running well...

Elgin number 41758229 is a grade 581, 21 jewel 16 size, made about 1942. Military B.W. Raymond model with sweep seconds...


Follow the album for this project here:

Job Number 260040

This has a broken balance staff, but also, oddly, the two-part roller table is not aligned. Not sure how that could happen...

Elgin number 41758229 is a grade 581, 21 jewel 16 size, made about 1942. Military B.W. Raymond model with sweep seconds...

Follow the album for this project here:

Job Number 250148

There's a lot of screws in these.

The underside of the mainspring barrel includes cut-outs for a Geneva Stop. The parts are missing though, as they almost always are. I don't know if Elgin stopped installing this complication at some point or if watchmakers servicing the watch left it out. These are very uncommon parts.

The Geneve Stop halts winding just before the end of the spring. It's not required for the watch to run perfectly normally, and it may not have been clear to some how to line up the gear when assembling the barrel.

The setting mechanism looks good. I'm optimistic that it won't need much effort to get it working correctly. A little too much wear on that flat spring and the inner wheel will not stay engaged.

The album for this project is here:

Elgin serial number 3793826 is a grade 70, 18 size, 15 jewels, made about 1890. This is a B.W. Raymond model.
As is often the case with older 18 size movements, my timing machine has trouble locking on. To sanity check the rate I have to go ahead and put the hands on, set it, and let it run for several hours. 

The basic rate test having gone well, I case it up and start with a few days of testing in positions. 

Job Number 250148

Here's a before image... It's pretty clean and all there.

This style of lever-setting mechanism is remarkably clever, but for good reason it wasn't used by Elgin for long. Note the setting wheel in the center with teeth both inside and outside. The tension on this, so is stays engaged on the cannon pinion, is critical and hard to get just right.


Elgin serial number 3793826 is a grade 70, 18 size, 15 jewels, made about 1890. This is a B.W. Raymond model.

Job Number 210157, Elgin Grade 240, B. W. Raymond

This one started out interesting. The mainspring is completely missing.

It's a motor barrel so the barrel came right apart as I disassembled. 

Broken balance staff...


The movement is an Elgin grade 240, 18 size, 19 jewels, B. W. Raymond model, made about 1909.


Installing a brand new, strong, alloy mainspring in Elgin's motor barrel is tricky and has to be done carefully. Should this spring go flying it could do serious injury. 
Assembly seemed to go well... at first.
The bevel pinion and clutch failed to rest in contact in winding mode. The movement wouldn't wind. Odd... 

At first I thought either of the parts might be an incorrect substitute. Some Elgin bevel pinions have an extra shoulder at the back that would perhaps cause it to sit further up. But I was able to determine that all these parts were correct by comparing them to a Veritas I happen to also have on the bench. The bevel pinion can move up, as shown here. But the clutch is as far back as it can go in winding mode in this image. What could the trouble be? Quite a mystery...

In the old Google+ days it was easy to turn this sort of thing into a watchmaking puzzle and post the answer later. Here, I guess I'll just go right ahead and divulge the problem.

On the dialside where the lever is, there is a spring loaded cam that pushes the clutch into winding mode "by default". When the lever is pulled out, it pushes the setting lever, and thus the clutch forward into setting mode.

The setting lever cam was installed incorrectly such that the spring pushed the clutch into setting position, and block it from going all the way back for winding. The direction the clutch push by default was the clue. The last person in this watch took the setting lever off and and put it back on the wrong side of its spring.

Next up, the pallet and balance staff.

The broken staff is removed by cutting away the hub in the lathe, then breaking the riveted side away in a staking set.


This shows riveting on the new staff.

Things often don't fit perfectly. I had to tighten the hairspring collet using this dedicated tool. 

The roller table for this movement is a double roller in two parts. I guess I didn't take a picture of that. It takes some extra careful work to assemble. You can see one of these here.

Running well so far...



I replaced one of the plate screws that was an incorrect style, and added a couple of timing washers. It's now ready for a few days of testing.

Job Number 210151, Elgin Grade 478

Here we have an Elgin grade 478 railroad grade watch. It is 16 size, 21 jewels, lever-set, made about 1928. It features a 10k gold filled open face case.


It had a broken mainspring but no other problems. Can you spot the break?







Both case and the movement are marked B. W. Raymond. The case mark is rather rare.


See the album for this project here:
https://photos.app.goo.gl/VWfGeppiZposjhvB7

Blog Archive