Job Number 260036
Elgin number 21877232 is a grade 291, 16 size, 7 jewels, made about 1919.
Job Number 260041
19 jewel, wristwatch, A-11 military. Black dial with sweep
seconds.
Follow the album for this watch here:
Job Number 260040
Elgin number 41758229 is a grade 581, 21 jewel 16 size, made about 1942. This is a military B.W. Raymond model with sweep seconds and a GCT dial.
Follow the album for this watch here:
Job Number 260012
I replaced each gear in the winding/setting mechanism one at a time to try to get at a specific rough spot in clockwise setting. I turns out that the minute hand squeezes the cannon pinion enough that it causes clockwise setting issue. I can't loosen the minute hand or it will falloff. I can't loosen the cannon pinion any further or the hands will slip and not move at all as the watch runs. I will have to work very carefully to alter where and how the cannon pinion grips along the center wheel shaft.
Just to make things extra complicated, there is barely enough space on these to allow the hands to pass each other, and to pass over the second hand, without colliding. The special issue with these Elgins though is that, as in the case with the keyless works, other manufacturing tolerances are not high enough to make these adjustments go smoothly. For example, the minute hand finds much less clearance above the hour hand on this watch when the hands are both down near 7:00.
Elgin number 4592421 is a grade 118, 6 size, 11 jewel, made about 1892.
Job Number 260040
The broken balance staff was not riveted on, or least it wasn't secure. I noticed it was loose while taking the roller parts off. The staff just pulled off, so I suppose that saves some time.
There's a two-piece double roller and the main part was very tight. I was afraid it would crack! I polish the staff body quite a bit (nice shine) and then went very slowly. It went on fine.
Sweep seconds...
New staff, now running well...
Elgin number 41758229 is a grade 581, 21 jewel 16 size, made about 1942. Military B.W. Raymond model with sweep seconds...
Job Number 260040
This has a broken balance staff, but also, oddly, the two-part roller table is not aligned. Not sure how that could happen...
Elgin number 41758229 is a grade 581, 21 jewel 16 size, made about 1942. Military B.W. Raymond model with sweep seconds...
Job Number 260038
So as not to leave any problems out (this watch is determined to have all the problems), the sleeve spring in the neck of the case was worn out. It's not broken, but is not tight enough. I replaced it.
Now the watch is finally ready for testing.
Elgin number 18167905 is a grade 294, 18 size, 7 jewels, made about 1915.
Job Number 260038
The roller jewel came loose, so it all had to come apart again.
It is reassembled and ticking though. We'll see how it goes.
Elgin number 18167905 is a grade 294, 18 size, 7 jewels, made about 1915.
Elgin number 18167905 is a grade 294, 18 size, 7 jewels, made about 1915.
Job Number 260038
A number of watches are giving me a hard time over the past week or so. Job numbers 260036 and job numbers 360012 are also bogged down.
On this one, I guess there must have been an undetectable crack in the balance pivot. The movement was left running over night but when I returned to it, the upper pivot was broken. I can't fully explain that but it has happened a couple of times before.
Elgin number 18167905 is a grade 294, 18 size, 7 jewels, made about 1915.
I know everyone is waiting. These things are a lot of work, and things move very slowly.
Replacement staff in progress...
Elgin number 18167905 is a grade 294, 18 size, 7 jewels, made about 1915.
Job Number 260038
This will need a fair amount of adjusting, I can tell already. Nothing is broken though.
Elgin number 18167905 is a grade 294, 18 size, 7 jewels, made about 1915.
Elgin number 18167905 is a grade 294, 18 size, 7 jewels, made about 1915.
Job Number 260036
Elgin number 21877232 is a grade 291, 16 size, 7 jewels, made about 1919.
Job Number 260036
The hands were in rough shape but I managed to save the hour and minute. The second hand was broken so I replaced that,
Elgin number 21877232 is a grade 291, 16 size, 7 jewels, made about 1919.
Elgin number 21877232 is a grade 291, 16 size, 7 jewels, made about 1919.
Job Number 260036
Cutting off the hub of the old staff off to remove the balance wheel...
The new staff is riveted on.
Both pivots had to be be reduced on the replacement staff but it spins feely.
The double roller assembly is seated down securely and the hairspring put in place and adjusted next.
Ticking well. I will let it run overnight then make further adjustment to the beat and timing.
The new staff is riveted on.
Both pivots had to be be reduced on the replacement staff but it spins feely.
The double roller assembly is seated down securely and the hairspring put in place and adjusted next.
Ticking well. I will let it run overnight then make further adjustment to the beat and timing.
Elgin number 21877232 is a grade 291, 16 size, 7 jewels, made about 1919.
job Number 260036
Elgin number 21877232 is a grade 291, 16 size, 7 jewels, made about 1919.
White 2137 Sewing Machine
And now for something completely different...
We found a sewing machine sitting free on the curb yesterday. It's a White model 2137 which as far as I can determine was in production in the later 1950s and early '60s.
We found a sewing machine sitting free on the curb yesterday. It's a White model 2137 which as far as I can determine was in production in the later 1950s and early '60s.
I have no experience with these things, but after a light surface cleaning, it was easy to determine that the motor worked. I didn't see anything obviously broken either.
Cleaned everything up... As is so often the case with items from this era is was coated in waxy brown buildup from cigarette smoke.
Cleaned everything up... As is so often the case with items from this era is was coated in waxy brown buildup from cigarette smoke.
I used silicone grease on its single plastic pinion and white lithium grease on all the cams. I opened up all the bearings and applied regular sewing machine oil. I used some rubber restoring stuff on the belt, and then made a couple adjustments. I didn't disassemble the motor, but it does go so maybe its best left alone anyway.
Subscribe to:
Posts (Atom)
Blog Archive
-
▼
2026
(144)
-
▼
October
(21)
- Job Number 260043
- Job Number 260036
- Job Number 260041
- Job Number 260040
- New Arrival, Job Number 260057
- New Arrival, Job Number 260043
- Job Number 260012
- Job Number 260040
- Job Number 260040
- Job Number 260038
- Job Number 260038
- Job Number 260038
- Job Number 260038
- Job Number 260036
- Job Number 260012
- Job Number 260036
- Job Number 260036
- job Number 260036
- Job Number 260012
- White 2137 Sewing Machine
- Job Number 260034
-
▼
October
(21)








.jpg)










































